Exam4Labs JN0-363 Dumps Real Exam Questions Test Engine Dumps Training [Q45-Q62]

Exam4Labs JN0-363 Dumps Real Exam Questions Test Engine Dumps Training

Juniper JN0-363 exam dumps and online Test Engine

NEW QUESTION # 45
Exhibit

Which two statements are correct about the service provider MPLS network shown in the exhibit? (Choose two.)

A. R3 is considered a PE router.
B. R3 is considered a P router.
C. R3 is considered an ingress router.
D. R3 is considered a transit router.

Answer: B,D

Explanation:
In a service provider MPLS network, P routers are interior routers that are used to transit MPLS-labeled packets between edge routers but do not attach or remove MPLS labels themselves. These routers are also referred to as transit routers. They are neither ingress nor egress routers (which are typically labeled as PE routers).
Reference:
Juniper Networks documentation on MPLS: MPLS Fundamentals

NEW QUESTION # 46
In your network, you have two LDP routers connected across four physical interfaces. You have also enabled LDP to operate on all four of those interfaces. What is the resulting outcome of your configuration between those two routers?

A. One session is built across four neighbor relationships
B. One session is built across one neighbor relationship
C. Four sessions are built across four neighbor relationships
D. Four sessions are built across one neighbor relationship

Answer: A

NEW QUESTION # 47
Which type of router can provide connectivity between areas in an IS-IS domain?

A. a Level 2 router with adjacencies in more than one area
B. a Level 1 router with adjacencies within a single area
C. a Level 2 router with adjacencies in a single area
D. an area border router with adjacencies in more than one area

Answer: A

NEW QUESTION # 48
Referring to the exhibit, which statement is correct?

A. R1 will advertise only the 10.200.3.0/24 prefix to the 192.168.1.5 neighbor.
B. R1 will advertise only the 10.200.1.0/24 prefix to the 192.168.1.5 neighbor.
C. R1 will advertise the 10.200.1.0/24, 10.200.2.0/24, and 10.200.3.0/24 prefixes to the 192.168.1.5 neighbor.
D. R1 will advertise only the 10.200.2.0/24 prefix to the 192.168.1.5 neighbor.

Answer: A

Explanation:
Referring to the configuration in the exhibit, R1 is set to export the 3rd_Policy to the neighbor at 192.168.1.5. Since 3rd_Policy permits the 10.200.3.0/24 prefix, only that prefix will be advertised to the neighbor.
Reference::
BGP Policies, Juniper Networks Documentation
Policy Framework, Juniper Networks Documentation
only 10.200.3.0/24 will be advertised. The neighbor export overrides anything at the group level and protocol level. Policies aren't additive, you can't apply all three at the same time. What if one of them rejected a prefix while the other accepted the same one? You need one to override the other

NEW QUESTION # 49
Which two routing protocols make use of a designated router, or pseudo node, to represent a broadcast network? (Choose two.)

A. BGP
B. IS-IS
C. MPLS
D. OSPF

Answer: B,D

NEW QUESTION # 50
Which two statements are true about VRRP? (Choose two.)

A. Interfaces within the same VRRP group must be on the same subnet for each member.
B. VRRP does not require redundant REs on each member.
C. Interfaces within the same VRRP group do not have to be on the same subnet for each member.
D. VRRP requires redundant REs on each member.

Answer: A,B

NEW QUESTION # 51
Click the Exhibit button. In the exhibit, all routers are sending routes to Router B

Which routes will be advertised from Router B to Router D?

A. BGP routes learned from Router A only
B. BGP routes learned from Routers A, C and E only
C. BGP routes learned from Router E only
D. BGP routes learned from Routers A and C only

Answer: B

NEW QUESTION # 52
Referring to the exhibit, internal BGP between R1 and R2 is not establishing.
What is the problem In this scenario?

A. R1 needs to be configured with an explicit router ID.
B. R1 and R2 must each have unique AS numbers.
C. R1 does not have a route to 192.168.200.2.
D. R1 needs to be configured with a next-hop self policy.

Answer: C

NEW QUESTION # 53
You configured interface ge-0/070.0 to run IS-IS. but this interface does not appear in the output of the show isis adjacency command as shown in the exhibit.

What is the problem in this scenario?

A. This is a Gigabit Ethernet interface, that is incompatible with the reference-bandwidth 100g statement.
B. The router at the other end of the link is a Level 1 only router.
C. The family iso statement must be added to the logical interface.
D. The router at the other end of the link Is not sending any IS-IS Hello messages.

Answer: C

NEW QUESTION # 54
What are tree types of interfaces that can be used in an MX Series device when implementing a virtual switch routing instance? (Choose three.)

A. GRE tunnel interface
B. Layer 2 logical interface
C. Trunk interface
D. Logical tunnel interface
E. Access interface

Answer: B,C,E

NEW QUESTION # 55
Click the Exhibit.

Your router has an external peering session to 10.10.25.5 and several internal peers. However, routes learned from EBGP peers are showing up in a hidden state on IBGP peers.
Where would you apply the policy shown in the exhibit to solve this issue?

A. Apply the next-hop-self as an export policy to the external BGP peers.
B. Apply the next-hop-self as an import policy to the external BGP peers.
C. Apply the next-hop-self as an import policy to the internal BGP peers.
D. Apply the next-hop-self as an export policy to the internal BGP peers.

Answer: D

NEW QUESTION # 56
Click the Exhibit button.

You have configured IPv6 over IPv4 tunneling, as shown in the exhibit. However, hosts connected to network 2001:0:0:1::0/64 cannot communicate with hosts on network 2001:0:0:2::0/64. The router R2 has a similar configuration as the R1 router.
How would you solve this problem?

A. Configure an IPv6 address on the tunnel interfaces
B. Configure the next hop of the inet6.0 static route to point to the physical interface between the routers
C. Configure an IGP across the tunnel interfaces
D. Configure the next hop of the inet6.0 static route to point to the IPv4 address of the remote router

Answer: D

NEW QUESTION # 57
You are bringing a new network online with three IS-IS routers using default Junos election priorities. The routers are configured as Level 2 only IS-IS routers. Which statement is true about the DIS election in this scenario?

A. The router with the lowest numerical lo0 IP address will be elected as the DIS.
B. The router with the lowest MAC address will be elected as the DIS.
C. The router with the highest numerical lo0 IP address will be elected as the DIS.
D. The router with the highest MAC address will be elected as the DIS.

Answer: C

NEW QUESTION # 58
Click the Exhibit button.

Your co-worker configures the ge-0/0/0 interface with an IPv6 address of 2001:db8:0:9::/64. After committing the configuration, your co-worker executes the command shown in the exhibit.
What is the fe80::206:aff:fe0e:e01/64 address in this scenario?

A. the loopback address
B. the multicast address
C. the link-local address
D. the statically assigned address

Answer: C

NEW QUESTION # 59
The segment touting SRGB start label Is 10,000 and the SRGB index range is 500.
In this scenario, which two statements are correct? (Choose two.)

A. The last usable label is 10.501.
B. The first usable label is 10,001.
C. The first usable label Is 10,000.
D. The last usable label is 10,499.

Answer: C,D

NEW QUESTION # 60
Which BGP message type is used to re-advertise routes that have already been sent to a peer and acknowledged using TCP?

A. refresh
B. update
C. keepalive
D. notification

Answer: B

Explanation:
In BGP (Border Gateway Protocol), the Update message is used to advertise new routes to a peer or to withdraw previously advertised routes. If there's a change in the routing information or if a new route needs to be advertised, BGP uses an Update message. This message is crucial for maintaining the most current and accurate routing information among BGP peers.
The other message types serve different purposes:
Keepalive: This message type is used to maintain the connection between BGP peers and ensure that the link is still active. Keepalive messages are periodically sent between peers when there is no other BGP activity to maintain the session.
Notification: This message is used to indicate errors or other significant events to a BGP peer. If a BGP error condition is detected, a Notification message is sent and the BGP session is typically closed.
Refresh: This is not a standard BGP message type. However, in the context of BGP, Route Refresh is a capability (not a message type) that allows a BGP router to request a full or partial re-advertisement of routes from a peer. This helps in re-synchronizing routing tables without tearing down the BGP session.
The BGP Update message is used to advertise routable destinations and includes route advertisements, route withdrawals, and path attribute modifications. Update messages are used to re-advertise routes that have already been acknowledged.
Reference::
BGP Operations and Message Types Overview, Juniper Networks Documentation BGP Update Message, Juniper Networks Documentation

NEW QUESTION # 61
Click the Exhibit.

Referring to the exhibit, which statement is correct about MVRP?